Corsair Hydro X Build Experience

We used the Corsair Hydro X set to best effect in our testing of the ASRock X570 Aqua. To complement the review, we decided to do a full system build featuring ASRock's AMD RX 5700 XT Taichi 8 GB graphics card and other hardware which Corsair provided. Everything bar the motherboard and the AMD Ryzen 3950X processor for this build was provided by Corsair. The full system specifications and test setup are located on the next page, although the full performance of power delivery thermals combined with Corsair's Hydro X parts can be found in our ASRock X570 Aqua review. As the ASRock X570 Aqua comes fitted with its own custom water block which cools the CPU, the power delivery on the motherboard, and the chipset, we didn't use any of Corsair's water blocks for this system.

The Corsair Hydro X Aqua System: All the AMD

Since we aren't using any of Corsair's CPU or GPU blocks for this system, all of the focus is on the core components themselves including the XD5 pump and reservoir combination, a single XR7 240 mm radiator, as well as Corsair's LL120 RGB 120 mm cooling fans and it's Softline range. We did intend to use an additional 360 mm cooling radiator, but the Corsair Crystal 680X with our hardware wasn't compatible due to the ASRock X570 Aqua's larger than normal E-ATX size. 


Testing possible hardware configurations inside the Corsair Crystal 680X

The first task before even unboxing the hardware was to work out which way it was going to be configured and routed around the Corsair Crystal 680X chassis. As our motherboard is E-ATX and this is technically for ATX motherboards, we did experience a couple of headaches. This wasn't to the detriment of Corsair, but more our hardware was just too big to fit in. As a result, we decided to go with a single 240 mm radiator to cool the CPU, power delivery, and chipset which the ASRock X570 Aqua block covers.

The Corsair Hydro X Series XD5 comes with mounting brackets to allow installation into various parts of a system. We decided to opt for the safer option and mount it to one of the 120 mm intake fans on the front. This was primarily to allow us to show off the XD5 in the front of the chassis, instead of mounting it in the rear chamber. The XD5 itself looks good with its nylon clear chamber, and the mounting kit is solid and sturdy.

Due to space constraints, we mounted a 240 mm radiator in a pull configuration which intakes air from the bottom of the chassis. We are using three Corsair LL120 RGB 120 mm fans in the front, with two on the radiator, and one in the rear as an exhaust. Each fan is connected to the Corsair Commander Pro controller which allows us to control everything from the Corsair iCUE software.


Drain port installation, should the worst happen

For better aesthetics, we routed one of the tubes through the rear chamber of the chassis, but this also allowed us to create less obstruction in the main chamber without needing to run tubing everywhere across components. For easy draining, we connected a ball valve which we can close for draining, and installed a drain port with plenty of tubing to drain without needing to dismantle the loop. This sits in the rear chamber at the bottom and is tucked away in front of the Corsair HX850 850 watt 80PLUS Platinum power supply.

After hours of countless routing and optimization of the tubing and layout, our system was complete. One thing about the Corsair Hydro X series is that it looks good, and is user-friendly making custom loop water cooling more accessible to consumers than ever before. What makes it more accessible is Corsair's Custom Cooling Configurator allows users to put in their hardware into the configurator and allow Corsair to work out what water cooling components are needed for whatever array of components are being used, or plan to be used. The Corsair Cooling Configurator is easy to use, intuitive and looks modern. This is something Corsair has put many months into designing for the end-user to make its buying decisions easy.

With the addition of the Corsair Commander RGB hub, we could connect all of the Corsair Hydro X series components including the fans and XD5 pump and reservoir combo up and sync everything up to the Corsair iCUE software; this includes the Corsair Vengeance Pro RGB memory. At present only ASUS hardware is certified to be used with Corsair iCUE in an exclusive partnership we learned about during CES 2020. As we are using ASRock hardware, we had to sync them up individually, but we like the contrasting look and having the ability to add effects.

Corsair Hydro X Series Overview Test Bed Setup and Thermal Performance
POST A COMMENT

71 Comments

View All Comments

  • Ninhalem - Wednesday, February 5, 2020 - link

    I am a custom water cooling builder and know how expensive the obsession can get, but I had to price check those fans. That's ridiculous to pay 130 USD for just 3 fans. You would be better off getting some nice static pressure fans like the EK Vardars and then slapping some Phantek's light rings on top of them than paying a little over 40 USD per fan. Reply
  • YB1064 - Wednesday, February 5, 2020 - link

    The cost is pretty high, but it looks and seems to perform well. Apart from the outrageously priced fans, perhaps one can find a cheaper pump+reservoir on EK's own website? Reply
  • Hxx - Friday, February 7, 2020 - link

    I’ve been building custom loops for years. Definitely check AliExpress / bykski/barrowch or if u don’t wanna wait then primochill ships from Utah . Fantastic high quality componentry without the premium bull from bitspower Corsair ek and the like Reply
  • hanselltc - Monday, February 17, 2020 - link

    Keep in mind you need aluminium parts though just to be cautious Reply
  • LedHed - Wednesday, February 5, 2020 - link

    Especially when you consider that you can buy Noctua NF-A14 iPPC 2000/3000 PWM fans for under $30 each!

    Personally, I'm going to go with industrial rated fans with a 6 year warranty (with a static of 4.18 mm H2O for the 2000 RPM), over some Corsair ones with RGB with static pressure below 2.0 mm H2O (for the 140mm model).
    Reply
  • Samus - Wednesday, February 5, 2020 - link

    I was just about to chime in this sentiment. I have 4 NF-A14’s in my silverstone FT03 and I’m pretty sure they were all under $100 shipped when I upgraded the fans from the crap Silverstone included. The A14 iPPC’s also ram massive amounts of air through radiators, negating the need for a push + pull configuration.

    Somehow I can’t believe the corsairs could do better unless they are a copy.
    Reply
  • jeremyshaw - Thursday, February 6, 2020 - link

    Wait, I have a FT03, too, it will barely fit three 120mm fans o.0
    All Noctuas, of course. The stock Silverstone fans on basically every case I have ever purchased from them were noisy and didn't move much air.

    Maybe it was the FT02 or FT05 (5 - 2 = 3 :P)?
    Reply
  • FatBoyDiesel - Wednesday, February 5, 2020 - link

    EK-Furious Vardar has 5.81mm H20 static pressure with a 500-3000RPM range. It's selling for $25 USD on EKWB's website and $21.99 at MicroCenter. Bought two of them and had no regrets. Reply
  • supdawgwtfd - Thursday, February 6, 2020 - link

    But... RGB! Reply
  • Azune - Friday, February 7, 2020 - link

    I bought one of those Noctua industrials fans some time ago as well. And while its true that they are very durable, they have one problem that makes them completely unusable for me.

    They have to spin at around 1000 RPM to even start. Which makes them very audible even when your PC is idle. I since have switched to their new NF-A12x25, which have a minimum RPM of 450, which makes them completely inaudible when idle.
    Reply

Log in

Don't have an account? Sign up now