‘How much does memory speed matter?’ is a question often asked when dealing with mainstream processor lines.  Depending on the platform, the answers might very well be different.  Similar to our comparisons with Ivy Bridge, today we publish our results for 26 different memory timings across 45 benchmarks, all using a G.Skill memory kit.

In our previous memory scaling article with an Ivy Bridge CPU, the results of memory testing between DDR3-1333 to DDR3-2400 afforded two main results – (a) the high end memory kit offered up to a 20% improvement, but (b) this improvement was restricted to certain memory limited tests.  In order to be more thorough, our tests in this article take a single memory kit, the G.Skill 2x4GB DDR3-3000 12-14-14 1.65V kit, through 26 different combinations of memory speed and CAS latency to see if it is better to choose one set of timings over the other.  Benchmarks chosen include my standard array of real world benchmarks, some of which are memory limited, as well as several gaming titles on IGP, single GPU and multi-GPU setups, recording both average and minimum frame rates.

The Problem with Memory Speed

As mentioned in the Ivy Bridge memory scaling article, one of the main issues with reporting memory speeds is the exclusion of the CAS Latency, or tCL.  When a user purchases memory, it comes with an associated number of sticks, each stick is of a certain size, memory speed, set of subtimings and voltage.  In fact the importance of order is such that:

1.      Amount of memory

2.      Number of sticks of memory

3.      Placement of those sticks in the motherboard

4.      The MHz of the memory

5.      If XMP/AMP is enabled

6.      The subtimings of the memory

I use this order on the basis that point 1 is more important than point 3:

  • A system will be slow due to lack of memory before the speed of the memory is an issue (point 1)
  • In order to take advantage of the number of memory channels of the CPU we must have a number of sticks that have a factor of the memory channels (point 2), known as dual channel/tri channel/quad channel.
  • In order to ensure that we have dual (or tri/quad) channel operation these sticks need to be in the right slots of the motherboard – most motherboards support two DIMM slots per channel and we need at least one memory stick for each channel
  • If the MHz of the memory is more than CPU is rated for (1333, 1600, 1866+), then the user needs to apply XMP/AMP in order to benefit from the additional speed.  Otherwise the system will run at the CPU defaults.
  • Subtimings, such as tCL, are used in conjunction with the MHz to provide the overall picture when it comes to performance.

A user can go out and buy two memory kits, both DDR3-2400, but in reality (as shown in this review), they can perform different and have different prices.  The reason for this will be in the sub-timings of each memory kit: one might be 9-11-10 (2400 C9), and the other 11-11-11 (2400 C11).  So whenever someone boasts about a particular memory speed, ask for subtimings.

G.Skill DDR3-3000 C12 2x4GB Memory Kit: F3-3000C12D-8GTXDG

For this review, G.Skill supplied us with a pair of DDR3 modules from their TridentX range, rated at DDR3-3000.  This is at the absolute high end of memory kits, with very few memory kits going faster in terms of MHz.  Of course, in this MHz race, it comes at a price premium: $690 for 8 GB.  This memory kit uses single-sided Hynix MFR ICs, known for their high MHz numbers, and while there are large heat-spreaders on each stick, these can be removed reducing the height from 5.4 cm to 3.9 cm.

Hynix MFR based memory kits are used by extreme overclockers to hit the high MHz numbers.  Recently YoungPro from Australia took one of these memory sticks and hit DDR3-4400 MHz (13-31-31 sub-timings) to reach #1 in the world in pure MHz.

Test Setup

Test Setup
Processor Intel Core i7-4770K Retail @ 4.0 GHz
4 Cores, 8 Threads, 3.5 GHz (3.9 GHz Turbo)
Motherboards ASRock Z87 OC Formula/AC
Cooling Corsair H80i
Intel Stock Cooler (pre-testing)
Power Supply Corsair AX1200i Platinum PSU
Memory G.Skill TridentX 2x4 GB DDR3-3000 12-14-14 Kit
Memory Settings 1333 C7 to XMP (3000 12-14-14)
Discrete Video Cards AMD HD5970
AMD HD5870
Video Drivers Catalyst 13.6
Hard Drive OCZ Vertex 3 256GB
Optical Drive LG GH22NS50
Case Open Test Bed
Operating System Windows 7 64-bit
USB 3 Testing OCZ Vertex 3 240GB with SATA->USB Adaptor

With this test setup, we are using the BIOS to set the following combinations of MHz and subtimings:

Almost all of these combinations are available for purchase.  For any combination of MHz and CAS, we attempt that CAS for all sub-timings, e.g. 2400 9-9-9 1T at 1.65 volts.  If this setting is unstable, we move to 9-10-9, 9-10-10 then 9-11-10 and so on until the combination is stable.

There is an odd twist when dealing with DDR3-3000.  In order to reach 3000 MHz, as Haswell does not accept the DDR3-3000 memory strap, we actually have to use the DDR3-2933 strap and boost the CPU speed to 102.3 MHz.  This leads to a slight advantage in terms of CPU throughput when using DDR3-3000 which does come through in several benchmarks.  In order to keep things even, our 4.0 GHz CPU has the multiplier reduced for 3000 C12 in order to keep the overall system speed the same, albeit with a slight BCLK advantage.

At the time of testing, DDR3-3000 C12 was the highest MHz memory kit available, but since then there are now 3100 C12 memory kits on the market taking price margins even higher at $1000 for 8 GB.  The problem at this speed is the actual overclocking of the CPU aspect of the system will skew the performance results in favor of the high end kit.


For this test, we use the following real world and compute benchmarks:

CPU Real World:
 - WinRAR 4.2
 - FastStone Image Viewer
 - Xilisoft Video Converter
 - x264 HD Benchmark 4.0
 - TrueCrypt v7.1a AES
 - USB 3.0 MaxCPU Copy Test

CPU Compute:
 - 3D Particle Movement, Single Threaded and MultiThreaded
 - SystemCompute ‘2D Explicit’
 - SystemCompute ‘3D Explicit’
 - SystemCompute nBody
 - SystemCompute 2D Implicit

IGP Compute:
 - SystemCompute ‘2D Explicit’
 - SystemCompute ‘3D Explicit’
 - SystemCompute nBody
 - SystemCompute MatrixMultiplication
 - SystemCompute 3D Particle Movement

For what should be obvious reasons, there is no point in running synthetic tests when dealing with memory.  A synthetic test will tell you if the peak speed or latency is higher or lower – that is not a number that necessarily translates into the real world unless you can detect the type and size of all the memory accesses used within a real world environment.  The real world is more complex than a simple boost in memory read/write peak speeds.

For each of the 3D benchmarks we use an ASUS HD 6950 (flashed to HD6970) for the single GPU tests, the HD 4600 in the CPU for IGP, and a HD 5970+5870 for a lopsided tri-GPU test.

 - Dirt 3, Avg and Min FPS, 1360x768
 - Bioshock Infinite, Avg and Min FPS, 1360x768
 - Tomb Raider, Avg and Min FPS, 1360x768
 - Sleeping Dogs, Avg and Min FPS, 1360x768

Firstly, I want to go through enabling XMP in the BIOS of all the major vendors.

Enabling XMP with ASUS, GIGABYTE, ASRock and MSI on Z87
Comments Locked


View All Comments

  • MrSpadge - Thursday, September 26, 2013 - link

    Is your HDD scratching because you're running out of RAM? Then an upgrade is worth it, otherwise not.
  • nevertell - Thursday, September 26, 2013 - link

    Why does going from 2933 to 3000, with the same latencies, automatically make the system run slower on almost all of the benchmarks ? Is it because of the ratio between cpu, base and memory clock frequencies ?
  • IanCutress - Thursday, September 26, 2013 - link

    Moving to the 3000 MHz setting doesn't actually move to the 3000 MHz strap - it puts it on 2933 and adds a drop of BCLK, meaning we had to drop the CPU multiplier to keep the final CPU speed (BCLK * multi) constant. At 3000 MHz though, all the subtimings in the XMP profile are set by the SPD. For the other MHz settings, we set the primaries, but we left the motherboard system on auto for secondary/tertiary timings, and it may have resulted in tighter timings under 2933. There are a few instances where the 3000 kit has a 2-3% advantage, a couple where it's at a disadvantage, but the rest are around about the same (within some statistical variance).

  • mikk - Thursday, September 26, 2013 - link

    What a stupid nonsense these iGPU Benchmarks. Under 10 fps, are you serious? Do it with some usable fps and not in a slide show.
  • MrSpadge - Thursday, September 26, 2013 - link

    Well, that's the reality of gaming on these iGPUs in low "HD" resolution. But I actually agree with you: running at 10 fps is just not realistic and hence not worth much.

    The problem I see with these benchmarks is that at maximum detail settings you're putting en emphasis on shaders. By turning details down you'd push more pixels and shift the balance towards needing more bandwidth to achieve just that. And since in any real world situation you'd see >30 fps, you ARE pushing more pixels in these cases.
  • RYF - Saturday, September 28, 2013 - link

    The purpose was to put the iGPU into strain and explore the impacts of having faster memory in improving the performance.

    You seriously have no idea...
  • MrSpadge - Thursday, September 26, 2013 - link

    Your benchmark choices are nice, but I've seen quite a few "real world" applications which benefit far more from high-performance memory:
    - matrix inversion in Matlab (Intel MKL), probably in other languages / libs too
    - crunching Einstein@Home (BOINC) on all 8 threads
    - crunching Einstein@Home on 7 threads and 2 Einstein@Home tasks on the iGPU
    - crunching 5+ POEM@Home (BOINC) tasks on a high end GPU

    It obviously depends on the user how real the "real world" applications are. For me they are far more relevant than my occasional game, which is usually fast enough anyway.
  • MrSpadge - Thursday, September 26, 2013 - link

    Edit: in fact, I have set a maximum of 31 fps in PrecisionX for my nVidia, so that the games don't eat up too much crunching time ;)
  • Oscarcharliezulu - Thursday, September 26, 2013 - link

    Yep it'd be interesting to understand where extra speed does help, eg database, j2ee servers, cad, transactional systems of any kind, etc. otherwise great read and a great story idea, thanks.
  • willis936 - Thursday, September 26, 2013 - link

    SystemCompute - 2D Ex CPU 1600CL10. Nice.

Log in

Don't have an account? Sign up now